New electric pallet truck 2 ton electric pallet jacks used in warehouse

Keyword:Electric Pallet Trucks   Time:2019-11-3 23:35:44

Twenty Inspection Rules for Electric pallet Trucks
 1.  Check the technical status of each part of the vehicle according to the stipulated items and standards, so that the electric pallet truck is in good condition.            

 2.  The fork must not be raised too high when the plant plug-in truck is running. Attention should be paid to whether there are obstacles scratching in and out of the work site or during driving. No braking or turning.            

 3.  Before starting, we should observe the surrounding conditions of pallet truck. (For pneumatic or braking vehicles, the reading of brake barometer must reach the prescribed value before starting). After confirming safety, we should start by whistling.            

 4.  Before driving, all kinds of documents necessary for driving such as vehicle driving license and driving license should be checked. It is strictly forbidden to drive without license, less license and no license.            

 5.  Drivers of pallet trucks in factories must strictly abide by the Standards for  Safety Management of Traffic in factories and the Code for Safety in Production.            

 6.  When a pallet truck is running in the factory, the height of the bottom of the  fork should be kept at 300-400 mm, and the gantry frame should be tilted  back.            

 7.  When a pallet truck works in a factory, it must rise and fall smoothly. If necessary, it must be securely sealed with ropes and chains. Cargo must be forked strictly according to the values specified in the load curve of the  vehicle, and overloading is strictly prohibited.           

 8. When a pallet truck is running, no one is allowed to get on or off the truck, and no people are allowed to  stand on the pallet legs.            

 9.  When pallet trucks in factories carry goods, the weight of the goods should be shared equally on two forks. The goods should not be skewed, and one side of the goods should be close to the shelf. Small cargo should be placed in the container (board) to prevent falling. Articles contained in the car plug-in shall not obstruct the driver's sight.           

 10. Foot brakes shall not be used for pallet trucks in factories when their loads are traveling over 7 degrees and going up and down at speeds higher than one gear.            

 11.  Brakes must be used to brake pallet trucks during loading and unloading. If the workpiece is loaded and unloaded by crane, the driver must leave the cab.            

 12.  Pallet trucks in factories are prohibited to suspend goods in the air after parking. After unloading, they should first land the crane and then drive.            

 13.  In factory areas and construction sites, the speed must not exceed 10 kilometers per hour, and in and out of factory doors, workshops, warehouses and construction sites, the speed must not exceed 3 kilometers per hour. When pallet truck is driving, pay attention to observation, prevent scratch and collision, and injure people.            

 14.  When lifting, lifting or driving pallet trucks in factories, it is forbidden for any personnel to stand on forks to control objects or play a balancing role. When pallets are lifted or lowered, no one is allowed near the pallet.            

 15.  When approaching or evacuating goods, the speed of fork should be slow and steady. Care should be taken not to crush goods, pad wood (pallet) and fork head to scratch support personnel.            

 16.  It is strictly forbidden to use forks and other lifters to work at high  altitudes, electric pallets, single forks or fork tops or pulls, braking inertia to slide round or rollable articles, and forks to overturn pallets for unloading. It is forbidden to fork articles at high speed.           

 17. When a fork is lifted or lowered, the lifting frame should be tilted forward with the ground, and the lifting frame should not be tilted forward.            

 18.  No direct palleting of goods on board the wharf or on the edge of the train carriage is allowed.            

 19.  When parking vehicles in factories, workshops and construction sites, drivers are not allowed to leave. If they need to leave temporarily, they must unplug the key and pull down the switch.            

 20.  When the pallet truck stops idling, the gantry frame should be tilted back. When the engine shuts down, the lifting slider should be lowered so that the fork is placed horizontally on the ground.

Competitive Electric Pallet Trucks China Supplier.jpg

Ramhoist News
  • No information
Ramhoist FAQ